保养真空泵的窍门

译文：
1.检查真空泵管路及结合处有无松动现象。用手转动真空泵，试看真空泵是否灵活。 2.向轴承体内加入轴承润滑机油，观察油位应在油标的中心线处，润滑油应及时更换或补充。 3.拧下真空泵泵体的引水螺塞，灌注引水或引浆。 4.关好出水管路的闸阀和出口压力表及进口真空表。 5.点动电机，试看电机转向是否正确。 6.开动电机，当真空泵正常运转后，打开出口压力表和进口真空泵，视其显示出适当压力后，逐渐打开闸阀，同时检查电机负荷情况。 7.尽量控制真空泵的流量和扬程在标牌上注明的范围内，以保证真空泵在最高效率点运转，才能获得最大的节能效果。 8.真空泵在运行过程中，轴承温度不能超过环境温度35℃，最高温度不得超过80℃ 。 9.如发现真空泵有异常声音应立即停车检查原因。 10.真空泵要停止使用时，先关闭闸阀、压力表，然后停止电机。 11.真空泵在工作第一个月内，经100小时更换润滑油，以后每个500小时，换油一次。 12.经常调整填料压盖，保证填料室内的滴漏情况正常以成滴漏出为宜.。 13.定期检查轴套的磨损情况，磨损较大后应及时更换。 14.真空泵在寒冬季节使用时，停车后，需将泵体下部放水螺塞拧开将介质放净。防止冻裂。 15.真空泵长期停用，需将泵全部拆开，擦干水分，将转动部位及结合处涂以油脂装好，妥善保管。

“ Vacuum pump maintenance tips ”是由中国离心泵网提供的国际水泵新闻，译文仅供参考。另外，中国离心泵网还提供相关产品搜索：离心泵型号、离心泵价格、离心泵技术、离心泵新闻、离心泵生产商等。

原文：
1. Check whether the vacuum pipe and the junction loosening. Hand rotation vacuum pumps, vacuum pump If we look at whether the flexibility. 2. To join the bearing lubrication oil bearing the body to observe the oil level should be the subject of the centerline at the oil, lubricating oil should be promptly replaced or supplemented. 3. Screw vacuum pump under the water pump drain plug, filling water or arguments pulp. 4. Off the road a good outlet pipe valve and exports and imports vacuum gauge manometer. 5. Jog motor, If we look at motor turn is correct. 6. Activate the motor, when the normal operation of vacuum pump, open the export and import of vacuum Self-priming centrifugal pumps for clean water or chemicalspressure gauge, depending on its display, after the appropriate pressure, and gradually open the valve, and check the motor load conditions. 7. Try to control the flow of vacuum pump and the lift on the plate within the scope specified in order to ensure the efficiency of vacuum at the highest point of operation in order to get the most energy-saving effect. 8. Vacuum pump during operation, the bearing temperature must not exceed the ambient temperature 35 ℃, the maximum temperature not exceeding 80 ℃. 9. If found to have abnormalFIJ series chemical centrifugal pump noise vacuum pump should be immediately stopped and check the reason. 10. Vacuum pump to stop when it is used to close the valve, pressure gauge, and then stop the motor. 11. Vacuum pump at work, within the first month, after 100 hours to replace oil, after every 500 hours, oil change time. 12. Regularly adjusting packing gland, packing the room to ensure drip drip out of the situation to normal in order to become suitable.. 13. Periodic inspection sleeve wear, the wear should be promptly replaced after larger. 14. Vacuum pump used in the Stainless steel chemical centrifugal pumpwinter season, parking, the need to turn on the water pump drain plug screw to open the lower part of the media put the net. Prevention of Frost Crack. 15. Vacuum pump long-term disabled, the need to pump all apart and wipe away moisture, and the combination of the rotating parts coated with grease installed at a good, safe custody.